Introduction of Clean Water Pump

Introduction of clean water pump:


  1.  The clean water pump is forbidden to clean new wells and pump muddy water

2. Qualified power supply, cable and start-up equipment (such as air switch, auto coupling decompression start box) must be equipped as required. The start-up The clean water pumpshall have the protection functions of short circuit, open phase, overload, etc. under the normal operation of the electric The clean water pump pump, the protection device shall not act.

3. When installing and using the electric clean water pump, it must be reliably grounded. It is forbidden to push and pull the electric switch with wet hands and feet. Before installing and repairing the electric pump, the power must be cut off. The place where the electric pump is used should be provided with an obvious sign "prevent electric shock".

4. Before entering the well, the inner cavity of the motor of centrifugal water pump must be filled with distilled water or non corrosive clean and cold boiled water. Tighten the water adding and discharging bolts. When the electric pump is running on the ground, it is necessary to fill the cavity with water to lubricate the rubber bearing, and start it for no more than one second in an instant to see whether the direction of rotation is the same as the direction of rotation. When the electric centrifugal water pump is upright, pay attention to safety to prevent it from overturning and hurting people.

5. Strictly follow the scope of application of lift and flow specified by the electric pump, to prevent the low lift and large flow or high lift and large axial force, so that the thrust bearing and other parts are extremely worn and the motor is overloaded and burnt.

6. After the electric centrifugal water pump is lowered into the well, the insulation resistance of the motor to the ground shall be measured to be no less than 100m Ω. After the start-up, the voltage and current shall be regularly observed, and the insulation of the motor winding shall be checked to see if it meets the specified requirements.

7. When the electric centrifugal water pump is stored, the water in the motor shall be drained to prevent the motor from freezing in winter.

horizontal centrifugal pump
Basic Info
  • Model NO.: IS65-50-160

  • Max.Capacity: 5.4-400cbm/H

  • Impeller Number: Single-Stage Pump

  • Position of Pump Shaft: Centrifugal water Pump

  • Impeller: Closed

  • Seal Type: Mechanical Seal or Packing Seal

  • Trademark: CB/OEM

  • Origin: China

  • Max.Head: 4-125m

  • Driving Type: Motor or Diesel

  • Influent Type of Impeller: Single Suction centrifugal water Pump

  • Pump Casing Combined: Horizontal Split Pumps

  • Usage: Pump

  • Color: Blue or as Customer′s Requirements

  • Transport Package: Standard Export Plywood Case

  • HS Code: 8413709990

Product Description
Standard Horizontal End Suction Centrifugal Pump with Electric Motor Sets

1) IS100-65J-200A
ISSingle-stage single suction centrifugal clear water pump
100Inlet diameter of pump (mm)
65Outlet diameter of pump (mm)
JRated speed dropped
200Impeller nominal diameter (mm)
AA,B.C seperately represents that impeller diameter is cut the first, the second and the third time.
centrifugal pumpsA few of Model information FYI, catalog can be sent if you are interested in: Company Information:
TypeCapacityHeadSpeedShaft Power Motor PowerImpeller Dia.Inlet Dia.Outlet Dia.
m³/hL/smr/minkwkwmmmmmm
IS50-32-1257.52.082229800.962.21275032
IS50-32-12512.53.472029801.132.21275032
IS50-32-125154.1718.529801.262.21275032
IS50-32J-1253.751.045.414800.130.551275032
IS50-32J-1256.31.75514800.160.551275032
IS50-32J-1257.52.084.614800.170.551275032
IS50-32-125A11.23.111629800.981.51155032
IS50-32-125A11.23.111629800.981.51155032
IS50-32-125A11.23.111629800.981.51155032
IS50-32J-125A5.61.56414800.120.551155032
IS50-32J-125A5.61.56414800.120.551155032
IS50-32J-125A5.61.56414800.120.551155032

Company Information



FAQ
1. Q: Are you a manufacturer or trading company?
    A: We are a professional clean water pump manufacturer with 30 years' experience.
 
2. Q: How to manage your quality?
   A: We make the whole process ourselves, we have trained QC inspect the details of each procedure to make sure everything is ok then move to next step.
Finally, each of our products will be tested with professional equipment before packing to ensure the quality.
 
3.Q:  I have purchase requirement but I am not sure which kind of pump is ok, can you help?
A: Yes, we'd love to help. You just need to advise some approximately information, like the range of capacity, head, liquid like oil or water? Then our engineer will recommed a few of matched options for you to choose.
 
4.Q: I can't find the one I want from your catalog, can you customize as my specification? How about OEM?
A: Yes. We have engineers' team who owns more than 20 years' experience in this field. They will design the pump as your information then arrange the production.
OEM is ok for us.
 
5.Q: What is your lead time?
A: Generally, there are 30 days after getting deposit. If there are some special requirements, like the project is really big or it needs to open the mould then we will discuss the delivery time in details.
But our factory will try best to meet your needs.

Welcome to contact us!

 centrifugal pump